Verified and Tested 02/28/15
This article will explain how to add two 3TB hard drives to an existing CentOS 6 system using PARTED and place them into a RAID1 software raid mirror.
PARTED, like fdisk, is a utility used to manipulate hard disk partitions. One advantage it has over fdisk is that it can handle provisioning disks whose volumes will span larger than ~1.9 TB in size.
Most Linux operating systems deploy with PARTED preinstalled. Should it not, use your favorite package installer(apt-get, yum) to acquire the software.
Creating 2TB or Larger Partition with PARTED
To do this, we have to partition the drives using PARTED, regular fdisk can’t do it (it doesn’t know how to handle anything over 1.9 TB), and mark the drives as GPT. We then use MDADM to create the software raid mirror.
For the example, the two new 3TB drives will be /dev/sdb and /dev/sdc
Partition disks using PARTED
parted -a optimal /dev/sdb
This will load you into the Parted CLI on /dev/sdb. Run the follow commands to make the disk GPT:
You should get a warning that says:
Warning: The existing disk label on /dev/sdb will be destroyed and all data on this disk will be lost.Do you want to continue? Yes/No?
Y and then run the following command to make your /dev/sdb disk set to ext4 and a primary disk starting at 0% and fill to 100%:
mkpart primary ext4 0% 100%
To see the partition that you made information use the following command:
Depending on your setup yuo will get something similar to the following:
Model: Msft Virtual Disk (scsi) Disk /dev/sdb: 3TB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 3TB 3TB primary raid
To flag your partition as Raid run the following command:
set 1 raid on
Perform the same procedure above for /dev/sdc.
Tell mdadm to create a RAID device called /dev/md0 by running the following command:
mdadm --create /dev/md0 --level=1 --raid-devices=2 /dev/sdb1 /dev/sdc1
mdadm: Note: this array has metadata at the start and may not be suitable as a boot device. If you plan to store '/boot' on this device please ensure that your boot-loader understands md/v1.x metadata, or use --metadata=0.90 Continue creating array?
Read the warning and hit
Y and you should get an output like the following:
mdadm: Defaulting to version 1.2 metadata mdadm: array /dev/md0 started.
Wait for the system to complete the sync process. Once completed, create a new directory and mount your new MD device.
To view your current partition set up run the following command:
You should get an output like the following:
Personalities : [raid1]
md0 : active raid1 sdc1 sdb1
10475392 blocks super 1.2 [2/2] [UU]
Create a new raid 1 directory by running:
Then mount your raid to your new raid 1 directory
mount /dev/md0 /raid1/
Next we need to update fstab and mdadm.conf
With your favorite editor open /etc/fstab and add the following to the last line of fstab file.
/dev/md0 /raid1 ext4 defaults 0 0
It should look similar to the following once done
# Created by anaconda on Fri Jun 20 09:39:24 2014
# Accessible filesystems, by reference, are maintained under '/dev/disk'
# See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info
UUID=bfc860b0-9d1c-41e9-984f-83166f20dc03 / ext4 defaults 1 1
UUID=e136ebe6-f2b8-4098-bd16-11a1fa6044e2 /boot ext4 defaults 1 2
UUID=911f21eb-7500-41cd-9c0d-e2d4ab822b55 swap swap defaults 0 0
tmpfs /dev/shm tmpfs defaults 0 0
devpts /dev/pts devpts gid=5,mode=620 0 0
sysfs /sys sysfs defaults 0 0
proc /proc proc defaults 0 0
/dev/md0 /raid1 ext4 defaults 0 0
Update madam with the following command:
mdadm --detail --scan > /etc/mdadm.conf
Congratulations! You’ve created a new RAID1 device using MDADM with GPT partitioning.
Thank you for following along this how-to! Please check back here for more updates, and to learn more about our cloud hosting solutions.